m u r 1 6 30 c t thru m u r 1 6 6 0 c t 16 amp super fast g l a ss p a s s i v a t ed r ectifier features maximum ratings operating junction temperature: -5 5 c to +1 50 c storage temperature: -5 5 c to +150 c microsemi catalog number device marking maximum recurrent peak reverse voltage maximum rms voltage maximum dc blocking voltage mur1630ct mur1630ct 300v 210v 300v MUR1640CT MUR1640CT 400v 280v 400v electrical characteristics @ 2 5 c unless otherwise specified average forward current i f(av) 16 a t c = 100 c peak forward surge current i fsm 125 a 8.3ms, half sine maximum forward voltage drop per element v f i fm = 8 a maximum dc reverse current at rated dc blocking voltage i r 5.0u a 50 0 ua t j = 25 c t j = 100 c 3 0 0 to 60 0 volts to-220ab inches mm
a .560 .625 14.22 15.88 b .380 .420 9.65 10.67 c .100 .135 2.54 3.43 d .230 .270 5.84 6.86 e .380 .420 9.65 10.67 f --- .250 --- 6.35 g .500 .580 12.70 14.73 h .090 .110 2.29 2.79 i .020 .045 0.51 1.14 j .012 .025 0.30 0.64 k .139 .161 3.53 4.09 l .140 .190 3.56 4.83 m .045 .055 1.14 1.40 n .080 .115 2.03 2.92 p i n 1 p i n 3 p i n 2 c a s e a b c k j i h g f e d n m l h p i n 13 2 *pulse test: pulse width 30 0 m sec, duty cycle 2% c j 80 pf measured at 1.0mhz, v r =4.0v mur1660ct mur1660ct 600v 420v 600v glass passivated chip superfast switching time for hight efficiency low reverse leakage current high surge capacity 1.50v 1.30v t j = 25 c maximum reverse recovery time i f =0.5a, i r =1.0a, i r r =0.25a 50ns trr t y pi c a l j un c tion capa c itan c e 16 3 0 -1640ct 1660ct www.kersemi.com
mur1630ct thru mur1660ct instantaneous reverse leakage current - microamperes versus percent of rated peak reverse voltage - volts average forward rectified current - amperes versus case temperature - c figure 3 forward derating curve 60 80 100 120 140 160 0 0 2 4 6 single phase, half wave 60hz resistive or inductive load amps c 8 12 16 instantaneous forward current - amperes versus instantaneous forward voltage - volts figure 1 typical forward characteristics volts 4 6 20 10 amps .2 1.2 .4 .6 .8 1.0 .01 .02 .04 .06 .1 .2 .4 .6 1 2 25 c 40 60 100 1.4 figure 2 typical reverse characteristics volts 40 60 200 100 amps 20 140 40 60 100 120 .1 .2 .4 4 .6 1 2 4 6 10 20 400 600 1000 160 t j =25 c 1660ct 1 100 4 0 25 50 75 8 figure 4 maximum non-repetitive forward surge current peak forward surge current - amperes versus number of cycles at 60hz - cycles amps cycles 2 6 10 20 60 80 40 00 100 125 150 1630ct-1640ct www.kersemi.com
|